| |
FortiAP-431F |
FortiAP-433F |
| Hardware Type |
Indoor AP |
Indoor AP |
| Number of Radios |
3 + 1 BLE |
3 + 1 BLE |
| Number of Antennas |
5 Internal + 1 BLE Internal |
5 External (RP-SMA) + 1 BLE Internal |
| Antenna Type and Peak Gain |
PIFA:
4 dBi for 2.4 GHz, 5 dBi for 5 GHz |
Omni directional rubber duck antenna:
4 dBi for 2.4 GHz, 6 dBi for 5 GHz |
| Frequency Bands (GHz) |
2.400–2.4835, 5.150–5.250, 5.250–5.350, 5.470–5.725, 5.725–5.850 |
| Radio 1 Capabilities |
Frequency Band: 2.4 GHz
Channel width: 4x4 20/40 MHz
Modulation: BPSK, QPSK, QAM64, QAM256, and QAM1024
MIMO chains: 4x4 service |
| Radio 2 Capabilities |
Frequency Band: 5.0 GHz
Channel width: 4x4 20/40/80MHz and 2x2 160MHz
contiguous Modulation: BPSK, QPSK, QAM64, QAM256, and QAM1024
Mimo chains: 4x4 service |
| Radio 3 Capabilities |
Frequency band: 2.4/5.0 GHz MIMO chains: 1x1 frequency scanning |
| Maximum Data Rate |
Radio 1: up to 1147 Mbps
Radio 2: up to 2402 Mbps
Radio 3: scan only |
Radio 1: up to 1147 Mbps
Radio 2: up to 2402 Mbps
Radio 3: scan only |
| Bluetooth Low Energy Radio |
Bluetooth scanning and iBeacon advertisement @ 6 dBm max TX power |
| Interfaces |
1x 100/1000/2500 Base-T RJ45,
1 x 10/100/1000 Base-T RJ45,
1x Type A USB, 1x RS-232 RJ45 Serial Port |
| Power over Ethernet (PoE) |
802.3at PoE default
1 port powered by 802.3at or 2 ports powered by 802.3af
- Full System functionality + USB support 1 port is connected to 802.3af - No USB support, Operate
in 2x2 mode with reduced power R1/R2 17dBm(Tx power) |
| Simultaneous SSIDs |
Up to 16 (14 if background scanning enabled) |
| EAP Type(s) |
EAP-TLS, EAP-TTLS/MSCHAPv2, PEAPv0/EAP-MSCHAPv2, PEAPv1/EAP-GTC, EAP-SIM, EAP-AKA, EAP-FAST |
| User/Device Authentication |
WPA™, WPA2™, and WPA3™ with 802.1x or Preshared key, WEP, Web Captive Portal, MAC blocklist and allowlist |
| Maximum Tx Power (Conducted) |
Radio 1: 2.4 GHz 24 dBm / 251 mW (4 chains combined)*
Radio 2: 5 GHz 23 dBm / 200 mW (4 chains combined)*
Radio 3: NA |
| Kensington Lock |
Yes |
Yes |
| IEEE Standards |
802.11a, 802.11b, 802.11d, 802.11e, 802.11g, 802.11h, 802.11i,802.11j, 802.11k, 802.11n, 802.11r, 802.11v, 802.11w,
802.11ac, 802.11ax (Wi-Fi 6), 802.1Q, 802.1X, 802.3ad, 802.3af, 802.3at, 802.3az, 802.3bz |
| SSID Types Supported |
Local-Bridge, Tunnel, and Mesh |
Local-Bridge, Tunnel, and Mesh |
| Per Radio Client Capacity |
512 clients per radio (Radio1 and Radio2) |
512 clients per radio (Radio1 and Radio2) |
| Cellular Co-existence |
Yes |
Yes |
| LED Off Mode |
Yes |
Yes |
| Reset Button |
Yes |
Yes |
| OFDMA |
Yes (UL and DL) |
Yes (UL and DL) |
| 2.4 GHz OFDMA |
Yes |
Yes |
| Spatial Reuse (BSS Coloring) |
Yes |
Yes |
| UL MU-MIMO 802.11ax mode |
Yes |
Yes |
| DL-MU-MIMO |
Yes |
Yes |
| HE-MU-MIMO |
Yes |
Yes |
| Enhanced Target Wake Time (TWT) |
Yes |
Yes |
| ZeroWait DFS/Agile DFS |
No |
No |
| Rogue Scan radio modes |
Background, Dedicated |
Background, Dedicated |
| WIPS / WIDS radio modes |
Background, Dedicated (recommended) |
| Packet Sniffer Mode |
Yes |
Yes |
| Spectrum Analyzer |
Yes |
Yes |
| Length x Width x Height |
8.27 x 8.27 x 2.22 inches (210 x 210 x 56.5 mm) |
| Weight |
2.16 lbs (0.98 kg) |
2.19 lbs (0.995 kg) |
| Mounting Options |
Ceiling, T-Rail, and Wall |
Ceiling, T-Rail, and Wall |
| Included Accessories |
Mount kit for Ceiling, T-Rail and Wall |
Mount kit for Ceiling, T-Rail and Wall. 5 RP-SMA Male dual-band dipole antenna |
| Power Supply |
SP-FAP400-PA-XX or GPI-130 |
SP-FAP400-PA-XX or GPI-130 |
| Power Consumption (Maximum) |
24.5 W |
| Humidity |
5 - 90% non condensing |
| Operating / Storage Temperature |
32–113°F (0–45°C) / -31–-94°F (-35–70°C) |
| Directives |
Low Voltage Directive • RoHS |
| UL2043 Plenum Material |
No |
No |
| Mean Time Between Failures |
> 10 Years |
> 10 Years |
| Surge Protection Built In |
Yes |
Yes |
| Hit-less PoE Failover |
Yes |
Yes |
| WiFi Alliance Certified |
Yes |
Yes |
| DFS |
FCC, IC, CE, Japan, Korea, Taiwan |
| Limited Lifetime Warranty |
Yes |
Yes |
Your message must be between 20-3,000 characters!
